Replace your weak OEM ball joints with these robust 300M replacements.  Tests prove our 300M ball joints are 3x stronger than OEM, and over 2.5x stronger than other aftermarket options! Designed to be regreasable and can be adjusted for wear! These ball joints are manufactured in the USA, and are backed by a lifetime warranty against breakage! Warranty does not cover the boot or component wear. Includes replacement snap ring.  ***Sold Individually***   Fitment: RZR XP 1000 ('14+) (lower and upper) RZR XP Turbo ('16+) (lower and upper) RZR Turbo S ('18+) (lower and upper) RZR RS1 ('18+) (lower and upper) Press Fit Diameter: 1.331" (Newer Models May Differ in Size Requirements)

Part # AIU-201010TR5721 Fits HCR Long Travel Polaris RZR and Ranger The all-new HCR tie rods by Assault have been built to fully complement our HCRLONG TRAVEL kit offerings. These tie rods have been designed around the Long Travel RZR and Ranger. Full-length tie rod made from 6061 Aluminum this full-length tie rod replaces the extension in the kit. I Easy 100% bolt on, no cut, no drill installation Stronger then factory Made of 6061 Aluminum Proudly Made in the USA Go EVERYWHERE Lifetime Warranty Finish : Black  Material : Aluminum +4.0" Barrel Series  *PLEASE NOTE YOUR YEAR IN CHECKOUT FOR CORRECT CLEVIS SIZE THREADS* Fitment : 2014-2021 Polaris RZR Turbo and Non Turbo ( HCR LONG TRAVEL ONLY)

YXZ1000R HD Tie Rod Kit - WR Edition Replaces the entire tie rod assembly including the weak inner shaft / ball Hex design for easy adjustment Low profile outer heim to clear every wheel we could find Inner clevis made specifically for this vehicle with the angle locks to keep from loosening Inner clevis with low profile pin / clip to clear original boot All components are coated to keep from rusting Easy to install! Uses your stock boots.  #10123

HCR Suspension's Can-am Maverick X3 Heavy-Duty Race Link Set Part#: MAV-05408 These links are built using 0.120" Wall Chromoly using heat treated ends and cut to length for the X3 72" models. Both ends are Right-hand threaded for securing the heims in place and ensuring they do not back. These Heavy Duty link replacements are mainly used for strengthening up your X3 over stock components, or make you race ready to finish the race. Link Set Contains: (6) 0.120" Wall Chromoly Links cut to length for 2 uppers, 2 middle and 2 lower links (12) 5/8-18 RH Heims with jam nuts Mis-alignment spacers NOTE: You will reuse the OEM fasteners

HCR Suspension's Polaris RZR 1000 S Long-Travel Suspension Kit Part #: RZR-04600 (GEN-05400) FEATURES  +5” Over kit adding 10” of overall track width  17” of travel  Manufactured with HCR Elite Material. This Custom Alloy Boasts 30% stronger tensile & yield strength compared to 4130 series Chromoly.  Custom Valved King 2.5 HCR Pure Race Series Shocks. CNC bent for accuracy  Laser Cut construction for precise fit and finish CNC 4130 billet mounting points for increased integrity   RCV Axles 4340 Series Chromoly  Compression Adjusters allowing 30% adjustment for all terrains and driving styles.  High Clearance Boxed A-Arm Design providing increased ground clearance and strength  Each piece is hand Tig welded for strength and aesthetics  OEM ball joints to maximize low speed steering, ease & smooth travel with less maintenance  New HD Sway Bar Mounts compatible with factory sway bar  100% Bolt-on installation using factory mounting points  Larger Delrin bushings for increased strength and durability   SHOCK PACKAGE Custom length & tuned 2.5 HCR Race series Kings are included with every HCR 900/ 1000 S Kit.  HCR black and silver color shock bodies. This custom valved and tuned shock package includes King's wide range compression adjusters standard; allowing up to 30% adjustment. The 20 position compression clickers offer fine tuned adjust-ability. You can soften your ride when just cruising or firm up the compression when hammering rough terrain or carrying additional payload. You’ll have the ultimate in performance regardless of your pursuit.   Kit Contains:- 4 Front A-arms- 4 Rear Control Arms- 4 Nitro full tip to tip axles- 4 ZBROS EXIT 2.2 Shocks- Hardware- Install Guide

HCR Suspension's Polaris RZR 900 S Long-Travel Suspension Kit Part #: RZR-04600 (GEN-05400) FEATURES  +5” Over kit adding 10” of overall track width  17” of travel  Manufactured with HCR Elite Material. This Custom Alloy Boasts 30% stronger tensile & yield strength compared to 4130 series Chromoly.  Custom Valved King 2.5 HCR Pure Race Series Shocks. CNC bent for accuracy  Laser Cut construction for precise fit and finish CNC 4130 billet mounting points for increased integrity   RCV Axles 4340 Series Chromoly  Compression Adjusters allowing 30% adjustment for all terrains and driving styles.  High Clearance Boxed A-Arm Design providing increased ground clearance and strength  Each piece is hand Tig welded for strength and aesthetics  OEM ball joints to maximize low speed steering, ease & smooth travel with less maintenance  New HD Sway Bar Mounts compatible with factory sway bar  100% Bolt-on installation using factory mounting points  Larger Delrin bushings for increased strength and durability   SHOCK PACKAGE Custom length & tuned 2.5 HCR Race series Kings are included with every HCR 900/ 1000 S Kit.  HCR black and silver color shock bodies. This custom valved and tuned shock package includes King's wide range compression adjusters standard; allowing up to 30% adjustment. The 20 position compression clickers offer fine tuned adjust-ability. You can soften your ride when just cruising or firm up the compression when hammering rough terrain or carrying additional payload. You’ll have the ultimate in performance regardless of your pursuit.   Kit Contains:- 4 Front A-arms- 4 Rear Control Arms- 4 Nitro full tip to tip axles- 4 ZBROS EXIT 2.2 Shocks- Hardware- Install Guide

HCR Suspension’s RZR XP 1000 Dual-Sport Long-Travel Suspension System ** CALL IN FOR CURRENT LEAD TIMES - 435-865-9282 Part # RZR-05400HCR's proprietary billet, slot and tab design and honeycomb boxed arms are built to withstand the beatings of rigorous off-road riding which achieving the optimal combination of strength and appeal. Kit Features:HCR alloy used to build every kit is 30% stronger than 4130 ChromolyEvery external weld is an internal plate structured into the designHCR kits run a 4130-heat treated billet end allowing all internal and external plating to be attached to this billet eliminating a potential weak point Billets are available in both ball joint and spherical applicationsHCR Shock tower to reduce compound leverage and achieve a better motion ratioAddition wheelbase of +3 inchesAdditional width of +4 inches per side Ground Clearance increased by 1.25 inches in the arm designRCV 4340 Chromoly extended axle barsKing 2.5 Series HCR Spec. shocks with a 2.5 piggyback up front and the 2.5 IBP in the back IBP Front Upgrade Intended for the Dune enthusiast, Racers, and those who like to push it that much harder. This upgrade extends the same internal bypass technology included in the rear shocks to all 4 corners. This patented needle-valve design allows for less bottoming and shock fatigue on square edges, G outs, long distance racing, jumping, etc. where the front end needs a little more. HIGH CLEARANCE RADIUS RODS The high links are recommended for the recreational trail rider or Rock crawler. These ALL NEW HCR Aluminum High Links are a great way to get clearance under the rear and avoid rocks while out on the trails. Additional cost to upgrade. *PLEASE NOTE IN CHECKOUT WHAT YEAR YOUR RZR IS FOR THE CORRECT HUB HARDWARE WILL BE EITHER 10MM OR 12MM*STRAIGHT RADIUS RODS These heavy-duty HCR Race links follow the same design as the standard radius rod with material increased to .120 wall tubing. The 5/8-18 heims are available in Right hand threads only. Additional cost to upgrade. Kit Contains: - 4 Front A-arms- 2 Rear Trailing arms- Tie-rod Extensions- Shock Tower- 4 RCV Axle bars- 4 King 2.5 HCR Spec. Shocks- 4 Radius Rods - Anodized Black - Heavy-Duty Backplate - Hardware Pack- Install guide *Does not come with trailing arm radial bearings (Replace with Polaris OEM hardware)*  MUST USE 4+3 OFFSET WHEEL WITH THIS KIT

HCR Suspension's RZR XP 1000 OEM Elite Suspension Kit Part #: RZR-05200 Following the design of HCR’s proven Dual-Sport Kit, the re-designed Elite series has been created for the serious dune enthusiasts who wants the addition strength without the weight. This new proprietary design lightens the product without compromise. The alloy used to manufacture the Elite kit is 30% stronger in tensile and yield strength compared to 4130 Series chromoly. The material endures several processes and is hardened for better wear resistance and overall strength. Every external weld is an internal plate structured into the design. While the cost-effective approach is to run tube ends for ball joints , all HCR kits run a 4130 heat treated billet end allowing all internal and external plating to be attached to this billet eliminating a potential weak point. Billets are available in both ball joint and Uniball applications. Kit Features: Laser Cut construction for precise fit and finish CNC'd Chromoly mounting points for increased integrity HCR Custom Alloy. Boasts 30% more strength than Chromoly High Clearance Boxed Front A-Arm Design 1.250 added ground clearance Each piece is Tig Welded by hand for strength and aesthetics Re-use of OEM ball joints to maximize low speed steering ease & smooth travel with less maintenance High-Clearance Rear Trailing Arms provide an increase of 1.25” in ground clearance 100% Proudly Made in the U.S.A Bolt-on installation using factory mounting points Trailing Arm Heavy duty Sway-bars and hardware with 4130 Heims 1.75" longer wheelbase for better high speed stability, hill climbing, and descents Larger front tube mounts are 1.25” in diameter with Delrin bushings for increased strength and durability. Factory Crush sleeves re-used   Kit Includes:  - 4 Front A-arms - 2 Trailing arms - Hardware - Rear sway bar Links - Install Guide NOTE: You will re-use OEM ball joints in the front A-arms unless you have ordered OEM equivalents, or if you order the Spherical Bearing upgrade, A-arm mounting bolts and nuts, Trailing arm radial bearings, trailing arm mounting bolts except the shock bolts, sway bar and hardware. No radius links are included in the kit and are an available option to purchase as an additional option. Minor relief cutting needed. 

HCR Suspension's RZR XP 1000 OEM Duner Front A-arm Kit Part #: RZR-05200-1 Following the design of HCR’s proven Dual-Sport Kit, the re-designed Elite series has been created for the serious dune enthusiasts who wants the addition strength without the weight. This new proprietary design lightens the product without compromise. The alloy used to manufacture the Elite kit is 30% stronger in tensile and yield strength compared to 4130 Series chromoly. The material endures several processes and is hardened for better wear resistance and overall strength. Every external weld is an internal plate structured into the design. While the cost-effective approach is to run tube ends for ball joints , all HCR kits run a 4130 heat treated billet end allowing all internal and external plating to be attached to this billet eliminating a potential weak point. Billets are available in both ball joint and Uniball applications. Kit Features: Laser Cut construction for precise fit and finish CNC'd Chromoly mounting points for increased integrity HCR Custom Alloy. Boasts 30% more strength than Chromoly High Clearance Boxed Front A-Arm Design 1.250 added ground clearance Each piece is Tig Welded by hand for strength and aesthetics Re-use of OEM ball joints to maximize low speed steering ease & smooth travel with less maintenance 100% Proudly Made in the U.S.A Bolt-on installation using factory mounting points 1.75" longer wheelbase for better high speed stability, hill climbing, and descents Larger front tube mounts are 1.25” in diameter with Delrin bushings for increased strength and durability. Factory Crush sleeves re-used Kit Includes:  - 4 Front A-arms - Hardware - Install Guide NOTE: You will re-use OEM ball joints in the front A-arms unless you have ordered OEM equivalents, or if you order the Spherical Bearing upgrade, A-arm mounting bolts and nuts.

HCR Suspensions RZR XP 1000 OEM Elite Trailing Arm Kit Part #: RZR-05200-2 Following the design of HCR’s proven Dual-Sport Kit, the re-designed Elite series has been created for the serious dune enthusiasts who wants the addition strength without the weight. This new proprietary design lightens the product without compromise. The alloy used to manufacture the Elite kit is 30% stronger in tensile and yield strength compared to 4130 Series chromoly. The material endures several processes and is hardened for better wear resistance and overall strength. Every external weld is an internal plate structured into the design.  Kit Features: Laser Cut construction for precise fit and finish CNC'd Chromoly mounting points for increased integrity HCR Custom Alloy. Boasts 30% more strength than Chromoly Each piece is Tig Welded by hand for strength and aesthetics High-Clearance Rear Trailing Arms provide an increase of 1.25” in ground clearance 100% Proudly Made in the U.S.A Bolt-on installation using factory mounting points Trailing Arm Heavy duty Sway-bars and hardware with 4130 Heims Kit Includes:  - 2 Trailing arms - Hardware - Rear sway bar Links - Install Guide *Does not come with radial bearings (Replace with Polaris OEM hardware)* NOTE: Trailing arm radial bearings, trailing arm mounting bolts except the shock bolts, sway bar and hardware. No radius links are included in the kit and are an available option to purchase as an additional option. Minor relief cutting needed.